Can you use PVC for furnace exhaust

Traditional gas-fired, forced-air furnaces produce hot combustion exhaust gasses and therefore need metal vent pipes, or chimneys. In contrast, modern high-efficiency condensing furnaces

What type of pipe is used for furnace exhaust?

PVC pipes are used on conventional and sealed combustion high-efficiency furnaces. This is because their combustion process produces and exhausts gases and condensate at a rapid pace, which would corrode metal materials in a short time.

Does PVC get hot?

The short answer: No. Explanation: PVC is a thermoplastic, and therefore, at some point it will begin to degrade and break down as it’s heated up. It just so happens that Schedule 40 PVC’s maximum operating temperature is 140 degrees Fahrenheit, around the same temperature that hot water gets to in most homes.

Can you use PVC pipe as exhaust pipe?

PVC pipe is fantastic for many different applications, and it is even sometimes used for duct and venting applications, but there are a few reasons why PVC pipe is not a great choice for dryer vents. … All that hot air and moisture running through the pipe for years is bound to do some damage.

What size is furnace exhaust pipe?

Your furnace will require a 2 or 3 inch vent pipe depending on your furnace size even though all of the furnaces have a 2 inch opening where the vent pipe connects.

Can I vent my furnace out the side of my house?

If your furnace has an AFUE rating of 90 percent or above, it will have a flue pipe that goes out of the side of your house. That’s because the combustion byproducts are in a liquid form, so they need to be drained out of your home in a similar way that the condensation from your air conditioner is drained outside.

Can you use PVC for water heater vent?

PVC is fine. As Jason mentioned, plastic (PVC or ABS) is ok to use as a venting material on powervented hot water heaters. They work by sending a huge amount of air in with the flue gases that it decreases the temperature of the exhaust going through the vent enough that it will not comprimise the vent.

Should my furnace exhaust pipe be hot?

It’s normal for your exhaust pipe and the exhaust to feel warm. It’s also normal to see icicles or other icy build-up around the pipe during freezing weather. If your pipe is very hot, call Breedlove Dobbs so we can have an experienced and qualified technician check it out.

How do you exhaust a high efficiency furnace?

To avoid this problem, high efficiency furnace venting requires the use of PVC pipes instead of metal pipes to remove the acidic condensate from your home. These PVC pipes are connected to the furnace and expelled outside. This high efficiency venting system must be installed when you install the new furnace.

Can you use foam core PVC for venting furnaces?

The Supplemental Information to the installation instructions for one of the largest manufacturers of cell core PVC piping, Charlotte Pipe, states “Never use PVC or ABS cellular core pipe for combustion gas venting”.

Article first time published on

What is CPVC vs PVC?

What are the differences between CPVC and PVC? The main difference between CPVC and PVC is the range of temperatures each is capable of withstanding. CPVC can handle temperatures up to 200° Fahrenheit, while PVC peaks at 140° Fahrenheit.

What size is PVC vent pipe?

Though it is quite common for 2″ and 3″ diameter pipe to be used for venting, 4″ and 6″ pipe may be used for larger appliances and those units operating in a commercial environment. Fortunately, for most home owners, it is easy to determine what size PVC pipe they have and which of our vent screens will work for them.

What temperature does PVC become toxic?

Active PVC pipes should never be heated beyond 158 degrees.

What temp can PVC pipe withstand?

The maximum recommended operating temperature for PVC pressure pipe is 140°F. PVC pipe and conduit becomes stiffer with decreasing temperature and more flexible with increasing temperature. As with dimensions and pressure capacity, published pipe stiffness figures are applicable only for 73°F operating temperatures.

What temp will PVC pipe melt?

PropertyValueMelt Temperature212 – 500 °F (100 – 260°C) ***Heat Deflection Temperature (HDT)92 °C (198 °F) **Tensile StrengthFlexible PVC: 6.9 – 25 MPa (1000 – 3625 PSI) Rigid PVC: 34 – 62 MPa (4930 – 9000 PSI) **Specific Gravity1.35 – 1.45

How do I size a furnace flue pipe?

To determine the main flue size, refer to Figure 3 and locate the square inch area of each individual flue size. Next, total the square inch areas and refer back to Figure 3 to determine the pipe size the total corresponds with. In our example, 78.54 square inches equal a 10″ pipe size.

How long can a furnace exhaust pipe be?

The maximum vertical distance you can run a furnace exhaust vent is about 15 feet. If there is a forced air inlet within 10 feet of the exhaust vent, the exhaust gas ventilation terminal should be positioned at least 3 feet above it.

Can you use cellular core PVC for furnace exhaust?

DO NOT use Cellular Core PVC/CPVC or Radel for venting exhaust.

Can I use PVC for tankless water heater vent?

The Rinnai Sensei tankless water heater offers 14 possible venting configurations and can use PVC, chlorinated polyvinyl chloride (CPVC), or polypropylene venting. … They tolerate higher temperatures up to 194 degrees and 230 degrees Fahrenheit, respectively, and can be used with condensing tankless units.

Which gas appliance category allows for plastic vent materials?

USE OF PLASTIC VENTS Plastic venting systems are commonly used with condensing boilers, furnaces, tankless water heaters, and mechanically vented tanked water heaters. These appliances are listed as Category II, III, and IV appliances.

Can I vent my gas furnace horizontally?

Direct Vents These furnace vents can be installed horizontally through an exterior wall, or vertically so exhaust fumes go out through the roof. Although more costly than a natural vent, a direct vent is also a more efficient and safer option.

Can I vent my gas furnace through the wall?

Both types of heating systems can vent horizontally through a building wall, but the exhaust products of high efficiency or condensing boilers and furnaces are generally cool and have different venting and combustible clearance specifications.

Can high efficiency furnaces be vented vertically?

Sidewall Venting (High efficiency appliances) Venting can also be vertically vented through the roof (be wary as there can be unforeseen problems with venting through the roof as they are not easily maintained). Separate venting pipes are an optimal choice here as well.

Can you install a high efficiency furnace with only one pipe?

It’s perfectly acceptable to have a high-efficiency furnace installed with one pipe.

Can you power vent a furnace?

Power venting (also called induced draft) may use the same flue design as natural venting options, with one exception: there is a powered fan in the flue that pulls toxic gases through. … The fan starts pulling air through the flue before the furnace turns on.

Does high efficiency furnace need outside air?

The architecture of high-efficiency furnaces means that they have their own fresh air intake. This means that they don’t use the air inside your home; rather, they draw air from outside. However, this doesn’t mean you don’t need an external fresh air intake because you’ve installed a 90% furnace.

Why do high efficiency furnaces use PVC pipe?

To combat this issue, high efficiency condensing furnace uses PVC pipes to extract the acidic water from your home. These are connected to the furnace and routed out to the side of your home. The venting system is installed at the same time as your high-efficiency furnace.

How hot does a gas furnace exhaust pipe get?

The pipe material temperature value is usually 86 to 100 degree F. The temperature should be taken outside of the furnace cabinet.

What is the temperature of gas furnace exhaust?

Appliance typeExhaust Temperature(oF)(oC)Gas-fired heating appliance, no draft hood460238Glass melting furnace1200 – 1600650 – 870Oil-fired heating appliance, residential560293

What type of PVC is used for venting?

Despite the confusion, the safe practice would suggest the use of PVC schedule 40 pipes for the air intake vent on the furnace and CPVC for the exhaust flue vent, given its higher service temperature.

What is the difference between solid core and cell core PVC pipe?

The inside and outside walls are solid PVC, while the inner core is cellular (or foamed) PVC, a material that includes tiny bubbles of entrained air. … For pipe manufacturers, the main advantage of cellular-core PVC is lower cost, since it requires less resin to make than solid pipe.