How do I pair my Lucci fan remote

Press and hold the “ ” button on transmitter for 3－5 seconds within 60 seconds of switching the power ON to the receiver of the ceiling fan. C. Turn ON and change the speed of the ceiling fan via the transmitter to check the operation and successful paring.

How do I sync my Lucci fan remote?

Press and hold the “ ” button on transmitter for 3－5 seconds within 60 seconds of switching the power ON to the receiver of the ceiling fan. C. Turn ON and change the speed of the ceiling fan via the transmitter to check the operation and successful paring.

Where is the DIP switch on a ceiling fan?

Setting DIP switches The DIP switches for the receiver are located on the flat surface of the receiver. The DIP switches for the transmitter are in the battery compartment. 4-4. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate.

How do you sync a remote with a fan?

Turn the power to your fan off for 5-10 seconds and then back on using the wall switch. Quickly press the ‘PAIR’ button on the back of the remote control. This step should be done within three minutes of restoring power to the fan. Your fan should turn on low speed indicating the pairing was successful.

How do I reset my ceiling fan remote?

First, you start by turning the fan off using its remote control. Then, you’ll need to wait; some brands ask to wait 15 seconds, though others may require as long as 30 seconds. Last comes the most critical step: in order to reset remote, press and hold the OFF button for about 10 seconds.

How do I reset my Lucci fan remote?

Remove the battery from the remote and then reinstall it. This will reset the remote. Step 3. Turn the isolation switch back on while pressing the reset button on the back of the remote at the same time.

How do you reset a fan?

1. Locate the fan’s wall switch or circuit breaker.
2. Flip the switch/breaker off and wait about 5 seconds.
3. Flip the switch/breaker on and wait for 5 more seconds.
4. Repeat this off/on process 3 more times (for a total of 4 times).
5. The reset is complete when the fan’s LED indicator turns green.

What is a DIP switch on a fan remote?

If the remote control is within range and has charged batteries, the ceiling fan and the remote control may not be on the right frequency. Ceiling fans have a dip (for “dual in-line package”) switch for setting the frequency. Follow these steps to set or reset the frequency of the ceiling fan.

How do you reset a dip switch?

1. Raise Switch-1.
2. Power the unit Off and On.
3. Lower and Raise Switch-1 three times.

Do ceiling fan remotes go bad?

The remote receiver varies the voltage and current to change the fan motor speed. But ceiling fan remote control units can go bad too. Before you even think about tearing the fan apart to diagnose a problem, replace the batteries in the transmitter first.

Article first time published on

Why my ceiling fan is not working?

This could be because the circuit breaker has tripped or is off. Check your panel to confirm this. If the circuit breaker works fine, it could be a problem with loose wiring and connections. Your ceiling fan could also stop working due to internal defects namely shot ball bearings or an overheated motor.

How do I turn my ceiling fan on without a remote?

To control a remote-controlled ceiling fan without using the remote, add a pull cord to the pull switch on the motor module. The pull cord can be purchased from a hardware store or garden and patio shop, while the tools needed are already in most households.

How do you program a fanimation remote?

Turn fan power on, press and hold SET button with a ball-pen or similar object on back of remote for 5 seconds within 60 seconds of powering fan in order to synchronize with fan motor.

Why does my fan work but not the light?

When you discover a ceiling fan light doesn’t work, confirm that electricity is reaching the room. Test your fan to see if the blades rotate when turned on. If the blades turn, check the switch that controls the ceiling fan light. … Reset the breaker and then test the ceiling fan light and blades.

Does a ceiling fan with remote need a wall switch?

While most ceiling fans are remote control adaptable, meaning a remote can be added if desired, there are some of fans that come with a remote and cannot have a switch installed (i.e. remote only). … That way only a single wall switch plate is required which keeps the wall looking cleaner and less cluttered.

How do you tell if a dip switch is on or off?

A DIP switch facing upwards is “on”, while a DIP switch facing downwards is “off”. DIP switches 1 through 5 are used to determine which address that the 4219 will be set to.

How do you test a dip switch?

Press HOME > More > Diagnostics > Frame Diagnostics > DIP Test. The menu shows the number of DIP switches on the Frame CPU board, what they do, and what position they are currently in.

Is there an app to control my ceiling fan?

Fan Remote 4+ Turn your Bluetooth Device into a convenient remote control for your ceiling fan. The “Fan Remote” app when paired with Home Depot’s Universal Bluetooth Remote can operate your fan by turning on/off, change speeds to high, medium, low, and control your light kit including dimming feature.