How do you reset Rainbird ESP

Press and hold the left and right arrow buttons at the same time for at least 3 seconds. Until you see the word “CLEARED” on the screen. Your ESP-Me is now restored to the factory default settings.

How do I reset my irrigation system?

1. Turn the control dial to the “off” position.
2. Press the “next” button to access the clear-memory feature. …
3. Press and hold the “off” button until the display stops blinking.
4. Turn the control dial to the “run” position.
5. Press and hold down the “minus” arrow and “prog” buttons simultaneously.

How do I reset my Rainbird wireless controller?

You can reset the controller password while connected to the Rain Bird WiFi controller in AP hotspot mode. Press the button on the LNK WiFi Module in the controller for 1 second. The light should change from blinking green to blinking green and red.

Why is my Rainbird not working?

Circuit breaker/fuse – Check the condition of the circuit breaker or fuse, if it has been blown the most likely reason is a field wiring short. An Electromechanical controller will stop on the station that caused the problem. Reset the controller to its rest position and replace the fuse or reset the circuit breaker.

Why are my sprinklers not popping up?

— A broken sprinkler head is one of the most common reasons that your pop-up sprinkler heads do not work properly, even when the water is turned on at a full blast. Broken sprinkler heads are easy to identify. Simply look for cracked casings, broken plastic pieces, or heads that refuse to pop-up out of the ground.

How do I reset my sprinkler controller?

1. Unplug the controller’s transformer.
2. Press and hold down the, and buttons.
3. Plug the controller’s transformer back in.
4. Release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.

How do I know if my Rainbird solenoid is bad?

1. The Water Won’t Shut Off. If you have this problem, it’s very likely the solenoid. …
2. Low or Uneven Water Pressure. The solenoid controls the water pressure. …
3. Water Leaks. There are many points in a sprinkler system that can leak. …
4. Current Testing. …
5. Valve Inspection. …
6. Parts Replacement.

How do you flush a Rainbird sprinkler system?

Manually flush the system. Turn on the water at the “shut-off” to supply your system, then operate the valves manually to flush the system. Open each valve to flush the pipe with water, then close.

What is the Rainbird controller password?

The controller password is restricted to letters and numbers, 4-8 digits in length. No special characters. If you use a special character it will not be registered in the password. As an example, if you typed in [email protected], the password would be stored as 1234.

How do you flush a Rainbird valve?

To flush valve to clear debris: Turn the bleed screw counter-clockwise ONLY 1 turn. Flush one minute and turn clockwise to close. Test and flush each line before sprinklers are attached. Several models of Rain Bird 24 Volt valves are available for home use.

Article first time published on

How do I increase the water pressure in my pop up sprinklers?

Remove a few sprinkler heads from each of the zones in your system and cap the plumbing that led to them. Decreasing the number of sprinkler heads will increase the water pressure in those that remain. Install a boost pump on the main irrigation line.

How do I find a sprinkler head that does not pop up?

Use a metal detector to find buried sprinkler heads. Many valves have metal parts you can locate by running the metal detector over the surface of the ground. Valves are located directly under sprinkler heads. Look for large, dry, brown spots in your lawn.

Should solenoid be on or off?

Avoid over-turning the solenoid in either direction, as this can cause damage to the components or cause pressurised water to escape the solenoid. When you hear water rush through the device, it’s easy to tell that the valve has opened successfully.

What happens when a sprinkler solenoid goes bad?

Water leaks: High pressure from a broken solenoid can put a lot of stress on your sprinkler system and burst small or large leaks throughout it. Low water pressure: Low water pressure can be just as much of a problem.

Why do my sprinklers come on twice?

A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.

How do I connect my Rainbird wireless controller?

Launch the Rain Bird app and press the Add Controller button. Follow app prompts to set up WiFi connection to Rain Bird controller. Share access to the controller as needed. Program and test controller by turning on watering at the timer and through the Rain Bird app.