What are shipping bolts on a Samsung washing machine

Your Samsung Front Load Washing Machine comes with shipping bolts inserted into the back of the machine to keep the tub secure during transportation. Suspension system of machine supports the wash tub while it tumbles and spins . Operating machine with locked tub (by shipping bolts) may damage internal parts.

What are shipping bolts on Samsung washer?

Your Samsung Front Load Washing Machine comes with shipping bolts inserted into the back of the machine to keep the tub secure during transportation. Suspension system of machine supports the wash tub while it tumbles and spins . Operating machine with locked tub (by shipping bolts) may damage internal parts.

Do you have to remove shipping bolts Samsung washer?

Samsung Front-loader washing machines uses a suspension system to support the washtub while it agitates and spins, However the system isn’t designed to withstand the strain of moving. … Before installing the washing machine, it is required that you remove all shipping bolts from the back of the unit.

What do washer shipping bolts do?

A transit bolt, also called a washer shipping bolt, is installed through the back a washing machine to keep the tub from moving around during shipping.

Can I move my washing machine without the transit bolts?

Moving a washing machine without transit bolts will run the serious risk of damaging your machine, so we strongly advise against it. … However, you must remember to remove the transit bolts once your move is complete, as they can seriously damage your machine should you begin a wash cycle with them still in place.

Are shipping bolts necessary?

The shipping bolts keep the tub secure during a move and reduce the amount of vibration that could damage the suspension. If you do not have the necessary shipping bolts, you can purchase them through an appliance repair center.

What happens if you don't remove shipping bolts from washer?

Failure to remove the shipping bolts and retainers before use may cause severe vibration and noise, which can lead to permanent damage to the washer. The second possible cause of excessive vibration is a shipping block that might be caught under the washer.

Why my Samsung washer shakes too much?

Check the load amount. A severely under loaded or overloaded washer will vibrate excessively. If you are washing one pair of jeans, add a few additional items to create a balanced load. If your washer is overloaded, try to remove a few items to create a balanced load.

Can transit bolts damage washing machine?

The bolts can rip sections off the outer tank, tear through the outer casing and cause massive damaging vibrations to be sent through the room in which the washing machine is installed. In other words, by not doing as instructed you risk major damage to your washing machine.

How do you transport a Samsung washer?

When you move your washer, first replace the shipping bolts that were originally in the back of the washer. This keeps the drum from moving inside the washer and protects it from damage. Also, make sure your washer is placed in the moving van upright. Shipping your washer on its side, front, or back can damage it.

Article first time published on

Where are the shipping bolts located on a washing machine?

So when front load washing machines are shipped from the factory, they’re shipped with shipping bolts in place. The shipping bolts are located on the back of your machine and they need to be removed before you can use it for the first time.

Do all new washing machines have transit bolts?

Normally when you get your new washing machine there will be two (rare), three or four transit bolts fitted through the rear panel of the washing machine that fix to the outer tank of the washing machine. … These bolts must be removed before the washing machine is used.

Do you need shipping bolts for top load washer?

Top-loaders usually require you to wedge foam or cardboard between the drum and the case. For a front-loader, you’ll typically insert shipping bolts in the rear of the washer to secure the drum. If you no longer have the original locks, contact the manufacturer to purchase some.

How do you secure a washing machine drum for transport?

Preventing a washing machine’s drum from excessive motion during your move will protect the suspension from breaking. You can do this by securing the drum with shipping bolts or transit bolts. These metal rods are inserted into special slots in the rear of the washer to secure the drum.

How do I stop my washing machine from jumping around?

1. Make sure the washing machine is level. Figure this out with a good old fashioned bubble level. …
2. Attach some non-slip, anti-vibration pads to the bottom of your washer’s legs. …
3. Take precautions to balance your washer load every time you do laundry.

How do you secure a washer without shipping bolts?

Impact of Moving A Front Load Washer Without Shipping Bolts: You can fill it with the help of the furniture blankets. You can remove the power cord and drain hoses, then wrap the washer with some dolly straps and then load it onto the dolly or truck for transport.

Is it OK to lay a washing machine on its side?

It’s recommended you always keep a washing machine in an upright position. Laying a washer on its side can cause the inner and outer tubs to bump against each other, which can loosen support pads or damage the suspension. It can also cause the tubs to move out of alignment and alter the way your unit works.

Why is my washer moving around?

Washing machine is not level – A shaking/vibrating washer is most commonly caused by the washer not being level. If the washer is slightly tilted to one side, the washer can shake and move around when running the spin cycle. There may be missing or damaged leveling legs.

How do you balance the drum on a Samsung washing machine?

1. Remove all laundry or any other contents in the machine.
2. Power off, and then power on the washing machine on again.
3. Hold down Temp.
4. Press START/PAUSE to run the Calibration cycle.
5. The drum will rotate clockwise and counterclockwise for about 3 minutes.

Why does my Samsung washer make noise when spinning?

The tub bearing helps to keep the inner tub spinning smoothly. If the washer is noisy during the spin cycle or is leaking from the bottom of the tub near the transmission, the tub seal and bearing are likely defective. … If the tub bearing is defective, we recommend replacing the outer tub and bearing at the same time.

How do I balance my Samsung washer?

1. 1 Tap Settings on your washing machines display.
2. Tap Calibration.
3. Tap Start. The washing machine door will lock and the drum will rotate clockwise and anticlockwise for several minutes. When your washing machine has finished calibrating, it will turn off automatically.