What should my flue temp be

You need at least 250 F all the way to the top to avoid water condensation and creosote formation. Depending on how tall your flue is and how well insulated what you have may be enough, wasted heat, or not sufficient.

How hot should flue pipe get?

I usually get the pipe to 500 – 550 upon initial start up and close down the air to run the. I would like to run the stove top temp to 600 as Jotul says the best range is 400-600. **All temp readings are the surface temperatures. 275 to 500 is what my manual says for my flue.

Where do you put a flue thermometer?

1. Place the Thermometer on the top, front, or side of a flat or curved surface. …
2. The optimum position is on the flue collar, or if not practical, as close to the collar as possible for a stable reliable place for monitoring the stove and flue gas temperature.

How hot does fireplace flue get?

A wood-burning fireplace can generate temperatures up to 1500 degrees Fahrenheit. But because wood burning is inefficient, the hard surfaces around the fire tend to get no hotter than 1000 degrees. A gas-burning fireplace tends to burn at a lower temperature, around 1000 degrees.

What temperature does a log burner flue reach?

To get the most heat from your wood burning stove, the temperature should be between 260 and 460°C. Any lower than this, your fire will be burning too slow to generate a good amount of heat.

What temp should I run my wood stove?

Depending on need I try to stay between 500°F & 700°F. Much higher and some of the steel will start to glow red. Your best creosote controls are if your wood is well seasoned and you have either an internal flue and/or your flue is insulated. Keep the flue gases warm and dry and you will not have a problem.

How hot is too hot for wood stove?

How hot is too hot when it comes to wood fire stoves and fireplaces? Anything over 800°F is starting to get too hot and could damage your wood stove or fireplace.

Will a hot fire remove creosote?

Creosote is a natural byproduct of burning wood in a wood stove or fireplace. … One method to loosen crusty or tarry creosote so it flakes off and falls down into the firebox or fireplace is to burn aluminum cans in a very hot fire.

How hot does double wall chimney pipe Get?

These pipes only need a 2-inch clearance to combustibles because they remain cool on the outside, while their internal design allows them to withstand temperatures as high as 1,700 or 2,100 degrees Fahrenheit for a limited time.

Do potato peels clean chimneys?

Burning the potato peels will not eliminate all soot or creosote buildup, but they will reduce it. A normal and regular chimney cleaning is still needed to keep the fireplace working properly and safely.

Article first time published on

Do I need a wood stove thermometer?

Your stove is rated to a specific KW output and attempting to raise this with more fuel will at best just be lost up the chimney, at worst, it will over-fire, decrease the lifespan of the burner and affect the terms of the manufacturer’s warranty. A thermometer allows you to avoid this costly user error.

Where do you place the Rutland burn indicator?

Install the Rutland Burn Indicator on vertical, single-wall pipe of a wood or coal stove.

What vents should be open on a wood burner?

Most wood burning stoves and multi-fuel stoves have a bottom air vent and a top air vent. Wood burns best with a good bed of ash laid down in the bottom of the stove and an air supply from the top. When lighting your stove, open both air vents fully.

How hot does creosote burn?

At approximately 1,100 degrees Fahrenheit, these gases, when mixed with the proper amount of air, break into flames and burn.

Does double wall chimney pipe get hot?

The outside of the double wall pipe is getting heating by both the direct heat coming from the stove top and the heat radiated by the hot flue gases. The point of the flue thermometer is to know the temperature of the flue gases heading up the inside of the pipe.

Is B Vent double wall?

AmeriVent Type B gas vent uses a double wall of metal pipe for insulation and safety. The inner pipe of reflecting aluminum heats quickly, containing the warm flue gases inside. The airspace between the inner and the outer pipes provides insulation against heat loss to keep the warmer flue gases on the rise.

Do chimney cleaning logs really work?

Many homeowners wonder if the chimney sweep logs or creosote sweeping logs really work to clean out fireplace flues and get rid of creosote residue so that the fireplaces are safe to use. The short answer is no, they don’t work. At least, not well enough to completely clean out the flue the way it should be cleaned.

What wood causes the most creosote?

In general, hardwoods like oak, ash, and beech are more difficult to ignite, but they last a long time. Softwoods like fir, pine and cedar make more smoke, and therefore more creosote.

What can I burn to clean my chimney?

1. Burning good wood.
2. Operating your fireplace or wood burning stove properly and.
3. Using the creosote sweeping log every few dozen fires, to prepare the chimney for its annual cleaning.

How often should you burn a creosote log?

For the best results, you should use one log for every 60 fires. If you’re not sure how frequently you use your chimney, keep track of every fire. You might hit 60 fires in two months, or it could take longer.

How do you make creosote remover?

A good creosote remover to use at least a few times a year is a mix of 1 tablespoon of mild dish soap and 4 cups of hot water. Wash down the stone, glass or metal and buff to a high shine. Repeat the process with this gentle creosote cleaner until the facade is free from creosote.

Does rock salt clean chimneys?

When it comes to DIY chimney cleaning, the obvious question is- what to burn to clean chimney, then rock salt is the first answer. Rock salts, combined with burning fire, have the ability to form a sort of mixture that moves through the chimney.

What is a flue collar?

Flue collars are essential parts of your heating appliance. It connects your vent piping to your chimney, allowing the smoke a place to escape. If your flue collar needs replaced or you need one to start with, this six inch diameter collar fits several models.

How does a wood stove thermostat work?

The Stove Stat operates as a thermostat, eliminating the need to manually control stove blowers. A heat sensor magnetically connects on the outer stove wall near the blower. When the sensor reaches a temperature of 110° F, the blower is automatically started. The blower is turned off as surface temperatures near 90° F.

Where do you put the thermometer on a wood stove pipe?

A stove top thermometer sits on top of the stove itself, and a magnet ensures it maintains a good connection. A stove pipe thermometer sticks to the stove pipe via a magnet and reads the temperature of the air passing through the pipe. Install it on the pipe approximately 12 inches above the stove top.

Are oven thermometers accurate?

The true temperature of the oven can be off by just a few degrees or up to 25 or even 50 degrees, which makes a big difference when you’re cooking something with very specific temperature needs, like meat or baked goods. An oven thermometer gives a more accurate temperature reading of the inside of your oven.

How do you install a stove pipe thermometer?

To install a probe thermometer, drill a 1⁄4 inch hole in the outer wall, and a 3⁄16 inch hole through the inner wall. Position so the thermometer can be read easily at a glance. Slide the magnet then the eyelet onto the stem of the thermometer; and insert into the hole.

What is the best stove fan?

• Tomersun 4 Blades Stove Fan. Excellent wood burning stove fan. …
• NETTA 4 Blade Woodburner Stove Fan. Super quiet operation. …
• Vonhaus 4 Blade Stove Fan with Temperature Gauge. Handy temperature gauge included. …
• Migaven Flue Pipe Stove Fan. …
• VOYTO Mini 4 Blade Heat Powered Stove Fan. …
• LUMAMU 5 Blade Stove Fan.

Does closing the damper on a wood stove?

By opening the wood stove damper, it allows air to get into the chimney so the fire can start. If you keep the damper open, the fire will build and the smoke and soot will vent through your chimney. … By closing the damper, it will reduce the oxygen levels in the chimney, and you’ll have a longer fire.

Should vents be open on log burner?

To keep a fire going in a wood burning stove, the air vents shouldn’t be fully open, but closed down enough so that enough air is being supplied to the fire to keep it going, without causing it to smolder.

Can you leave the door open on a wood burning stove?

Wood burning stoves are not designed to be used with the door open. You can use a wood burning stove with the door open but doing so will lose the control of the air flow into the stove, making it operate less efficiently and sending more heat up the chimney rather than out into the room.