Where do you nail cedar shingles

Nails should be long enough to penetrate underlying materials in the cedar shingles at least 3/4 inches, or all the way through. Use two fasteners to apply each Certi-label shingle or shake. Apply both nails 3/4 inches from the edge of each shake or shingle, and about 1 1/2 inches above the exposure line.

How do you nail cedar shingles?

Nails should be long enough to penetrate underlying materials in the cedar shingles at least 3/4 inches, or all the way through. Use two fasteners to apply each Certi-label shingle or shake. Apply both nails 3/4 inches from the edge of each shake or shingle, and about 1 1/2 inches above the exposure line.

What are the best fasteners for cedar shingles?

The Cedar Shake & Shingle Bureau prefers the use of nails, however if you choose to use staples they must be stainless steel Type 316 in locations within fifteen (15) miles of salt water. For locations outside of the salt water zone – stainless steel staples Type 304 or Type 316 must be used.

Can you use a roofing nailer for cedar shingles?

“Use either rust-resistant staples or shingle nails (1-1/4” to 1-1/2” long), galvanized, in stainless steel or aluminum”. … It simply means that the best nail gun for cedar shingles will either be a stapler nail gun or any nailer that can shoots the recommended nails or staples!

How many nails are in a square of cedar shingles?

Most shingle manufactures recommend using four nails per shingle on the main area of your roof and five nails per square in the first row of roofing. This adds up to an average of 320 nails or 100 square feet.

What nails do you use for cedar siding?

Hot-Dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and all can be used to nail Western Red Cedar. Other types of nails are not recommended. They can rust and disintegrate and react adversely with the natural preservative oils present in cedar resulting in stains and streaks.

How do you keep cedar shingles looking new?

If you have weathered and discolored wood siding, you can regain the new look of cedar by cleaning off the dirt and mildew with a solution of one third cup liquid household detergent (be sure it is ammonia-free), one quart liquid household bleach (containing 5% sodium hypochlorite), and three quarts warm water.

Can you use screws for cedar shingles?

Each Certi-label Western Cedar shingle or shake should be applied with two corrosion-resistant fasteners, such as stainless steel (type 304 or 316), hot-dipped zinc coated, or aluminum nails or other fastener as accepted by your local building official.

Can you use screws on cedar siding?

Do not use common nails or screws. Use of these will lead to eventual bleeding of rust over time, causing an unsightly stain in the cedar siding. Use only hot dipped galvanized, aluminum, or stainless steel nails or screws when fastening Western Red Cedar.

Can you use a nail gun for cedar siding?

With some overlap in nail size, you may wonder whether framing nailers can be used for siding? The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing.

Article first time published on

Can you use brad nails for shingles?

Large-body nailers typically include framing nailers and roofing nailers. These nailers are used for more technical projects such as framing out a basement or installing roofing shingles. … For woodworking projects, a brad nailer is a good choice.

What is the difference between a roofing nailer and a siding nailer?

Both tools are coil nailers that are built to drive nails into wood, but you can’t use them interchangeably. … Siding nailers are for installing siding and roofing nailers are meant for installing roofing.

Can I use galvanized nails in Cedar?

Hot-dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and all can be used to nail Western Red Cedar. Other types of nails, such as electroplated, are not recommended.

How do you install cedar shingles on a shed?

1. Cover the roof in felt roofing paper.
2. Install a cedar breather if needed.
3. Use a chalk line to align the starter course of cedar shingles.
4. Install shingles using 2” weather-resistant nails.
5. Install the first course directly on top of the starter course.

How many nails do I need for cedar siding?

Siding TypeThickness (in.)Nail SizeBevel3/42-1/4 (7d)7/8 & greater3 (10d)Boards, Tongue & Groove, and Channel5/82 (6d)3/42 (6d)

What size roofing nail should I use?

Roofing nails should be 1-1/4 to 2 inches long to ensure that it sufficiently penetrates and embeds in the roof sheathing. To calculate the appropriate roofing nail length, add the thickness of the shingles and underlayment to the thickness of the sheathing. Nail shank diameter should be at least 11-12 gauge for roofs.

How do I measure my roof for nails?

Multiply the length of each area by the width to determine the square footage. Add the amount of square footage for each area together. This will give you the entire square footage of the roof and will allow you to estimate the number of shingles, and thus nails, needed.

Should you seal cedar shingles?

No. Never seal your cedar roof. Sealing the roof will lock in moisture that would otherwise naturally evaporate during normal weather conditions. Cedar needs to breathe and thus a water repellant type product, rather than a water proofer is the best route to follow.

Can you oil cedar shingles?

The reason you may wish to consider a cedar roof oil treatment is that the natural oils in your cedar roof that keep your cedar shingles in good order and looking the way they should deteriorate over time. … This is why many people choose to treat their cedar roof with an oil treatment.

Should you stain cedar shingles?

Staining cedar shingles not only enhances their beauty but also fortifies them against threats posed by the elements. … To protect new shingles, apply a penetrating stain. Stain soaks in and protects the wood from the weather, and it won’t crack, peel, or chip.

How do you nail channel cedar siding?

Installing Lap or Channel Siding Do not nail through overlaps. For siding up to 6 inches wide, use one nail one inch up from the lap. Face nail with two nails per piece for 8 inches patterns and wider, keeping nails 2-1/2 to 3 inches apart to allow for dimensional movement without splitting.

Can you use roofing nails for siding?

Just remember that siding nails and roofing nails are not the same, and they cannot be used in place of one or the other. In most situations, you want separate nails for the two separate tasks.

Does cedar siding need furring strips?

Cedar is a material that needs to be allowed to flex once installed. It is highly recommended that the product be installed over furring stripes that are attached to the studs of a wall. For siding that is being installed in a horizontal pattern, the furring strips should be attached vertically.

Are nails or screws better for siding?

Although ring-shank siding nails are suitable for wood siding installation, screws have better holding power over time.

Is it better to nail or screw siding?

Nails are often preferred for structural joining, including framing walls, because they are more flexible under pressure, whereas screws can snap. Nails are also called upon when securing plywood sheathing for exterior walls, installing hardwood floors, and attaching siding and roofing.

What kind of screws do you use with cedar?

Cedar,” of the Western Red Cedar Lumber Association (WRCLA). The best option is stainless steel, which is the least likely to react with water and salt. At bare minimum, fasteners should be hot-dipped galvanized, in which the nail or screw is coated with zinc to protect it from corrosion, meeting ASTM A153.

Are nails or screws better for cedar fencing?

Nails are faster than screws to install, meaning less labor for you or your builder (which may translate into lower installation cost). However, nails are more likely than screws to grow loose over time. Screws, on the other hand, secure the fence better than nails.

What do roof nails look like?

All roofing nails have wide, flat heads and short shanks. The tips of the nails are sharp and pointed for easy insertion so you don’t break the shingles or damage the wood when driving the nails through. Different roofing materials require different types of roofing nails.

What nails do I use for siding?

Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig.

What is a brad nailer?

A brad nailer is a powered nail gun that shoots 18-gauge brads (small nails). Brad nailers are used by woodworkers and especially finish carpenters to install casing and base trim up to 3/8 inches thick. … Most brad guns can shoot brads that range in length from 5/8 inches to 2 inches.

Is a brad nailer the same as a nail gun?

Brad nails are formed from a fine, 18-gauge wire, which means they are smaller in diameter and typically have less holding strength. The benefit to an 18-gauge brad is its size. … Finish nailers will run 15- or 16-gauge finish nails, in both angled and straight varieties depending on the tool.