Why do you need a drip edge

Drip edge is metal flashing installed at the edges of the roof to keep water away from your fascia and from getting underneath your roofing components. If your roof doesn’t have drip edge, water gets behind your gutters and rots out both your fascia board and roof decking.

Is drip edge really necessary?

Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.

Where do you put drip edge?

The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.

Do you have to use drip edge on roof?

The 2012 International Building Code (IBC) requires drip edges for that type of roof. Regardless of the kind of roof you have, we highly recommend installing drip edges. Keep in mind that improper installation of any roofing component can create gaps, rendering any waterproofing solution useless.

Should gutters go under drip edge?

It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. … If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.

Should drip edge be tight to fascia?

A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.

Can you install drip edge after shingles?

Can Drip Edge Be Installed After Shingles? The most popular time to install a drip edge is when new shingles are installed. However, the drip edge can be installed at any time. The materials involved include: a ladder, a flat pry bar, a hammer, tin snips, eave stripping, and galvanized roofing nails.

What is the difference between gutter apron and drip edge?

A drip edge, which is installed along the eaves and roof edge, directs the water away from your fascia board and into the gutter. On the other hand, a gutter apron has the advantage of providing you with less maintenance over time. Gutter flashing or gutter apron serves the primary purpose of collecting all the water.

Do metal Roofs need a drip edge?

A drip edge is not needed for metal roofing. If you make sure to overhang your metal roofing at least an inch, the drip edge is not necessary at the eaves and rakes. If the metal roof is hanging over an inch, the water will be directed away from the fascia anyway if at a slant.

Does drip edge go on top of tar paper?

The drip edge should be over the paper at the eaves, and under along the rake. mroberson: Its a TRAP! Back in my construction days, I learned that you place the tar paper OVER the drip edge on the eaves so if moisture gets through the shingles, it does not get under the drip edge.

Article first time published on

Does drip edge go over or under felt?

Does Drip Edge Go Over or Under Felt? According to most building codes and manufacturer recommendations, the drip edge should be installed beneath the underlayment along the eaves of the roof.

Does drip edge go on first?

Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

Why is rain dripping between gutter and fascia?

Water Gets Behind the Gutter If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter.

Why is water dripping from my fascia?

If the water is coming from a leak between the gutter and the fascia, it is very likely that this is a gutter problem and that the back of the gutter was not installed correctly.

How far should shingles extend past drip edge?

Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off.

Can you face nail drip edge?

Not really. The whole idea of attaching drip edge by nailing into the roof sheathing from above, is to avoid providing a pathway for water to reach the wood underneath. Face nailing with regular nails will work themselves lose and provide that path. There are times it can not be avoided.

Should fascia be screwed or nailed?

Replacement fascia requires 4d galvanized casing nails. … Hometime.com recommends using screws instead of nails when replacing fascia to avoid jarring the existing framing with hammering.

Can you replace drip edge without removing shingles?

The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.

Why does water leak from soffits behind gutters?

If the gutters are clogged, it’s possible that the water is overflowing the gutters and this is contributing to the leak. If the gutters look clear, run a hose and fill the gutters with water. Water should run out the downspout and away from the house without filling the gutter.

How much does it cost to install drip edge?

The standard drip edge used (aluminum) is going to be around $2.00 a linear foot, including labor to install. If you upgrade to a different metal (steel or copper), it’s going to cost even more.

Does a metal roof affect insurance?

Metal. Metal roofing has a combination of positives that will not likely raise your home insurance rates. It handles rain, wind, hail and snow well, and is fire and rot-resistant, and has an average lifespan of 40 to 70 years.

How much overhang should a metal roof have?

A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.

Do I need a drip edge on rake edge?

A drip edge should be installed on the eaves and rakes of the roof, flush with the decking and fascia. On eaves, the drip edge is installed directly to the deck with underlayment installed over it for proper water shedding. On rakes, the underlayment is installed over the drip edge.

What is the difference between flashing and drip edge?

The drip edges main function on the eaves is to help the water drip over the roof, away from the facia and into the gutters. The metal flashing has a small metal flange that wicks water back to make a drip around the flange and into the gutter where it can be diverted away from the roof.

Why do you put tar paper under shingles?

Roofing felt or felt paper, also called underlayment or roofing tar paper, goes between the roof deck and the shingles, which adds another layer of protection to your roof. … It serves as a water repellent when heavy rain and storms can cause moisture to get trapped between the shingle and wood of your roof decking.

Can you put tar paper over shingles?

Answer: Roofing felt is a layer of tar paper installed beneath the shingles to provide a backup waterproof membrane in case of leakage. Felt, otherwise known as underpayment, is required when asphalt shingles are installed as a first layer of roofing or when they are applied over wood shingles or a built-up roof.

Can gutter leak into house?

If you are experiencing water leaking from your gutters into your house, the likely cause is clogged gutters. … In addition to roof leaks, clogged gutters can create a breeding ground for birds, rodents, and insects that can also find their way into your home over time.

Can full gutters cause a roof leak?

Clogged gutters are more than just a hassle to clean, as they can actually cause damage to your home, leading to roof leaks during heavy rain. Unclogged gutters are designed to channel water through the gutter trough, into the downspouts, and away from your home.