What is a blade buster

Description. Blade Buster. A safe, sure way to hold the blade of your push or riding lawn or riding lawn mower stationary while loosening and removing blade bolt. Easy to affix and operate – makes the job of blade removing easy and safe.

How do you stop a lawn mower blade from spinning?

Loosen the clamp on a blade removal tool by turning the handle counterclockwise. Place the removal tool over the end of the blade and the stopping edge over the side of the deck. Turn the handle clockwise to tighten it in place and prevent the spindle from turning.

What causes a lawn mower blade to keep coming loose?

One common cause of loose blades is actually running over a rock, trunk or anything solid. That kind of impact can do some serious damage to a blade, and if it’s bent it could end up ruining your crankshaft, which will basically KO your mower and make it useless. So before you proceed to tighten the blade.

What size is the nut on a lawn mower blade?

The retainer nut on most of our riding mower blades are a 5/8″ thread diameter. This sized thread diameter nut normally requires a 15/16″ wrench or socket tool in order to remove/install.

How sharp should a lawn mower blade be?

In general, you will want your lawnmower blade sharpened to about a 30-degree angle. The blades should be sharp enough to cut the grass without tearing or ripping it, but not so fine that the edge is razor-thin and easily damaged by the terrain or small debris in your lawn.

Do lawn mower blades have reverse threads?

Most lawnmower blade nuts are reverse-threaded in order to secure the blade on the drive shaft of the engine. This ensures that the blade’s rotation does not loosen the nut. However, not all blades use a reverse-threaded nut to secure them to the engine’s drive shaft.

How do mower blades engage?

When the clutch solenoid is energized, the clutch engages the drive belt to drive the rotation of the lawn mower blades. If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. … If the PTO switch is defective, replace it.

How often should you sharpen lawn mower blades?

This keeps your mower in good shape and helps to maintain a healthy lawn. However, if you mow more often, the blades will need more attention. On average, a mower blade should be sharpened after every 20 to 25 hours of use time.

How often should lawn mower blades be replaced?

A good rule of thumb for the average homeowner is to replace your mower blades annually. You may also think about replacing them if they become damaged. Dig up that product manual if you want a more clear-cut answer. Always make sure to take protective measures whenever sharpening your mower blades at home.

Does a new lawn mower blade need to be sharpened?

As mentioned above, brand new lawn mower blades do not need to be sharpened because they are always sharpened during manufacturing. … However, lawn mower blades do generally need to be sharpened at the beginning of each new season.

Article first time published on

Which way do teeth face on table saw?

Like miter saws, table saw blades rotate clockwise, meaning the teeth should be pointing down. Circular saw: Circular saws are the most commonly used power saw. They can accommodate a variety of blades for cutting wood and other materials such as masonry, plastic and metal.

What tools are required to change the blade?

Steps to Take Most saws have an attached wrench, either an Allen type or a blade wrench with a hole that fits over the arbor nut. The wrench is incorporated or attached to the saw handle, or otherwise “hidden” on the saw body.

Can you do freehand sawing with a table saw?

Do not make free-hand cuts on a table saw. Guide the stock through the blade using the rip fence or the miter gauge. … Work should be released only when it is past the blade.

Which side of mower blade faces down?

To determine which side of your lawn mower blade is up, first figure out which side is the sharp cutting edge, and which side is the blunt edge. Look for a sticker indicating which side goes up and which side faces downward. The cutting edge should face the grass while the dull edge should face the deck of the mower.

What size blades do I need for a 42 inch deck?

2 blades are required for a 42″ cut deck. This blade replaces Poulan/Craftsman 134149 and 532134149; Husqvarna 532 13 41-49. Blade measures 21″ long by 2-1/4″ wide with a 5 point star center hole.

Are lawn mower blades hard to replace?

Blades wear out with use and need to be changed occasionally to make your mower more efficient. You’ll keep your lawn healthier and you’ll need to mow less frequently with sharp, clean blades. Replacing them is an easy project that won’t take up much time, as long as you approach it correctly.

Can you replace lawn mower blades?

Mower blades can be sharpened several times to extend their life and ensure that your grass gets a healthy cut, but they can only be filed so many times before a blade replacement is necessary. … New mower blades tend to be reasonably priced, and mower blade replacements usually only require the use of a wrench.

Can you turn a riding lawn mower on its side?

Originally Answered: Is it OK to tip a lawn mower on its side? yes it’s ok but you need to keep carb side up so oil doesn’t drain into it. Gas shouldn’t leak out if all parts are working correctly. I usually tip it backwards to sharpen/change the blade and to clean the underside of deck.

Do I really need a torque wrench for lawn mower blade?

A torque wrench is critical for jobs like lawn mower blade fitting and flywheel fitting, as you already know, overtightening these components could cost you an engine.

What size bolt holds on mower blades?

You are correct it is a 15/16 head that you will need a stock number 15/16 45892 1/2 drive socket.   The shaft is 5/8 with 18 thread cut. I would suggest that you also purchase a 1/2 breaker bar also if you do not have on to get enough torque on the nut to remove tighten.

How do you remove a nut from a lawn mower blade?

Put a wrench socket of the correct size on the head of the bolt securing the blade to the blade holder, and apply force to the wrench handle in the counterclockwise direction to loosen the blade bolt. The bolt may have a 1/2-inch, 5/8-inch or 3/4-inch head, depending on mower model.

Should I use Loctite on mower blades?

High Strength Red Threadlocker is perfect for some key areas such as the bolts that hold the motor to the deck of a snow blower or lawn mower. In these situations, specifically a product like LOCTITE® 271™ High Strength Threadlocker works best.

How tight do lawn mower blades need to be?

How tight should lawn mower blades be? – Quora. Most rider should be around 70–90, if you don’t have a torque wrench this is very snug. I have hit things in the past and end needing a break over bar to get the blade off.

Why are my mower blades not engaging?

Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.

Should a mower blade be sharp to touch?

Mower blades should be aggressively sharp, but not as sharp as a razor’s edge. You should be able to touch the blade with your hand without getting cut. Contrary to popular belief, a lawn mower blade with a razor sharp edge will not cut grass better.

Does a lawn mower blade have to be razor sharp?

Mower blades should be sharp, but they do not need to be as sharp as a razor blade. When you touch the blade, you should not cut your hand. That way, they will cut the grass seamlessly and have a clean but. Very sharp blades will get dull quickly and need to be sharpened much more often, shortening the blade life.

Does wet grass dull mower blades?

Cutting wet grass can dull the blade more quickly. Clean blades thoroughly before and after mowing a lawn when wet to keep the cut as sharp as possible. … Maintain your machine and sharpen mower blades regularly to deliver a clean, healthy cut.

Why won't the blades engage on a Craftsman riding lawn mower?

Common solutions for: Craftsman Lawn mower blades won’t engage. … If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.

What does the deck engagement cable do?

It is the cable that allows a user to engage and stop mower blades. Over time the cable can get damaged or worn eventually breaking and requiring a replacement.